diff --git a/overlay/opt/emcomm-tools/bin/et-audio b/overlay/opt/emcomm-tools/bin/et-audio
new file mode 100755
index 0000000..0850755
--- /dev/null
+++ b/overlay/opt/emcomm-tools/bin/et-audio
@@ -0,0 +1,102 @@
+#!/bin/bash
+#
+# Author  : Gaston Gonzalez
+# Date    : 31 October 2024
+# Purpose : Configures ET audio device with sane defaults
+#
+# Preconditions
+# 1. Supported audio interface is connected and properly detected
+#
+# Postconditions
+# 1. ASLA settings set on ET audio device
+
+usage() {
+  echo "usage: $(basename $0) <command>"
+  echo "  update-config   - Update amixer config"
+}
+
+if [ $# -ne 1 ]; then
+  usage
+  exit 1
+fi
+
+start() {
+  update-config
+}
+
+update-config () {
+
+  # 1. Check if the symlink was created by the udev rules
+  if [ -e /dev/et-audio ]; then
+
+     # 2. Check that this device was properly tagged with the ET_AUDIO env variable with a udev rule
+     APLAY_OUT=$(arecord -l | grep ET_AUDIO)
+     if [ $? -eq 0 ]; then
+
+       # Use device descriptor assigned by udev rules
+       ET_DEVICE=$(udevadm info /dev/et-audio | grep ET_DEVICE)
+       if [ $? -ne 0 ]; then
+         et-log "ET_DEVICE not set by udev rule. Can't set ALSA settings"
+         exit 1
+       fi
+
+       ET_DEVICE_NAME=$(udevadm info /dev/et-audio | grep ET_DEVICE | cut -d"=" -f2)
+       AUDIO_CARD=$(echo $APLAY_OUT | cut -d":" -f1 | awk '{print $2}')
+       AUDIO_DEVICE=$(echo $APLAY_OUT | cut -d"," -f2 | cut -d":" -f1 | awk '{print $2}')
+       FULL_AUDIO_DEVICE="$AUDIO_CARD,$AUDIO_DEVICE"
+
+       et-log "Updating audio device: '${ET_DEVICE_NAME}' (${FULL_AUDIO_DEVICE})' for ALSA PnP configuration."
+
+       case ${ET_DEVICE_NAME} in
+         "DIGIRIG_MOBILE")
+           # Unmute Speaker a set volume. Adjust if remote station can't decode you. Your TX controls.
+           amixer -q -c ${AUDIO_CARD} sset Speaker Playback Switch 42% unmute
+           # Unmute Mic
+           amixer -q -c ${AUDIO_CARD} sset Mic Playback Switch 52% unmute
+           # Set "L/R Capture" to 19. Adjust if you can't decode received audio. Your RX controls.
+           amixer -q -c ${AUDIO_CARD} sset Mic Capture Switch 31% unmute
+           # Disable Auto Gain Control
+           amixer -q -c ${AUDIO_CARD} sset 'Auto Gain Control' mute
+
+           et-log "Applied amixer settings for ${ET_DEVICE_NAME}"
+         ;;
+         "DIGIRIG_LITE")
+           # Unmute Speaker a set volume. Adjust if remote station can't decode you. Your TX controls.
+           amixer -q -c ${AUDIO_CARD} sset Speaker Playback Switch 42% unmute
+           # Unmute Mic
+           amixer -q -c ${AUDIO_CARD} sset Mic Playback Switch 52% unmute
+           # Set "L/R Capture" to 19. Adjust if you can't decode received audio. Your RX controls.
+           amixer -q -c ${AUDIO_CARD} sset Mic Capture Switch 31% unmute
+           # Disable Auto Gain Control
+           amixer -q -c ${AUDIO_CARD} sset 'Auto Gain Control' mute
+
+           et-log "Applied amixer settings for ${ET_DEVICE_NAME}"
+         ;;
+         *)
+           el-log "No ALSA configuration specified for this ET_DEVICE."
+         ;;
+       esac
+
+     else
+       et-log "No ET_AUDIO device detected. Can't change ALSA settings."
+       exit 1
+     fi
+  else
+    et-log "No ET_AUDIO device plugged in. Can't change ALSA settings."
+    exit 1
+  fi
+}
+
+case $1 in
+  start)
+    start
+    ;;
+  update-config)
+    update-config
+    ;;
+  *)
+    echo "Invalid command."
+    usage
+    exit 1
+  ;;
+esac
diff --git a/overlay/opt/emcomm-tools/bin/et-js8call b/overlay/opt/emcomm-tools/bin/et-js8call
index dedad8d..4474709 100755
--- a/overlay/opt/emcomm-tools/bin/et-js8call
+++ b/overlay/opt/emcomm-tools/bin/et-js8call
@@ -2,7 +2,7 @@
 #
 # Author  : Gaston Gonzalez
 # Date    : 24 October 2024
-# Updated : 28 October 2024
+# Updated : 31 October 2024
 # Purpose : Wrapper script for starting JS8Call with PnP support
 #
 # Preconditions
@@ -62,7 +62,15 @@ update-config () {
        APLAY_OUT=$(arecord -l | grep ET_AUDIO)
        if [ $? -eq 0 ]; then
          AUDIO_DEVICE=$(echo $APLAY_OUT | cut -d"," -f2 | cut -d":" -f1 | awk '{print $2}')
-         JS8_AUDIO_DEVICE="plughw:CARD=ET_AUDIO,DEV=${AUDIO_DEVICE}"
+
+         # JS8Call has an issue decoding the received audio following a 
+         # transmission when the device below is used. 
+         #
+         #JS8_AUDIO_DEVICE="plughw:CARD=ET_AUDIO,DEV=${AUDIO_DEVICE}"
+         #
+         # Instead, the following device solves this issue:
+         JS8_AUDIO_DEVICE="sysdefault:CARD=ET_AUDIO"
+  
          et-log "Using '${JS8_AUDIO_DEVICE}' for JS8Call configuration."
 
          # 3. Check for existing JS8Call sound configuration
@@ -83,6 +91,9 @@ update-config () {
            echo "SoundOutName=\"${JS8_AUDIO_DEVICE}\"" >> ${JS8CALL_CONF_FILE}
          fi
 
+         ## Configure ALSA settings for sound card
+         /opt/emcomm-tools/bin/et-audio update-config
+
        else
          et-log "No ET_AUDIO device detected."
          notify_user "Can't start JS8Call. No ET_AUDIO device detected."
diff --git a/overlay/opt/emcomm-tools/bin/et-system-info b/overlay/opt/emcomm-tools/bin/et-system-info
index fcc9879..8dc6702 100755
--- a/overlay/opt/emcomm-tools/bin/et-system-info
+++ b/overlay/opt/emcomm-tools/bin/et-system-info
@@ -2,7 +2,7 @@
 #
 # Author   : Gaston Gonzalez
 # Date     : 6 October 2024
-# Updated  : 25 October 2024
+# Updated  : 30 October 2024
 # Purpose  : Utility script for dumping system information
 
 function usage() {
@@ -102,14 +102,21 @@ case $1 in
       # 2. Check if the rigctl systemd unit is running properly
       systemctl status rigctld --no-pager > /dev/null 
       if [ $? -eq 0 ]; then
-     
+    
+        # Note: I am disabling the VFO read as it causes issues with serval Icom 
+        # radios and results in the VFO changing momentarily during this client
+        # request. It causes issues during TX and RX. If it is not bulletproof,
+        # features like this will be turned off. This is a problem given that 
+        # Conky calls this method every 10 seconds.
+        #
         # 3. Grab and format frequency 
-        FREQ=$(timeout 1 rigctl -m 2 f)
-        if [ $? -eq 0 ]; then
-          printf "%'d MHz\n" "$FREQ" | sed 's|,|.|g'
-        else
-          echo "Connected. Can't access VFO"; 
-        fi
+        #FREQ=$(timeout 1 rigctl -m 2 f)
+        #if [ $? -eq 0 ]; then
+        #  printf "%'d MHz\n" "$FREQ" | sed 's|,|.|g'
+        #else
+        #  echo "Connected. Can't access VFO"; 
+        #fi
+        echo "Connected"; 
       else
         echo "Connected. No rig control"
       fi
diff --git a/scripts/install-audio-tools.sh b/scripts/install-audio-tools.sh
new file mode 100755
index 0000000..7964376
--- /dev/null
+++ b/scripts/install-audio-tools.sh
@@ -0,0 +1,13 @@
+#!/bin/bash
+# Author  : Gaston Gonzalez
+# Date    : 30 October 2024
+# Purpose : Install audio tools
+set -e
+
+et-log "Installing audio tools..."
+
+apt install \
+  audacity \
+  ffmpeg \
+  sox \
+  -y
diff --git a/scripts/install.sh b/scripts/install.sh
index 203ae9f..9f825a4 100755
--- a/scripts/install.sh
+++ b/scripts/install.sh
@@ -2,7 +2,7 @@
 #
 # Author  : Gaston Gonzalez
 # Date    : 16 March 2024
-# Updated : 13 October 2024
+# Updated : 30 October 2024
 # Purpose : Main installer for EmComm Tools OS Community
 
 . ./env.sh
@@ -36,3 +36,5 @@ exitIfNotRoot
 ./install-conky.sh
 
 ./install-direwolf.sh
+
+./install-audio-tools.sh