diff --git a/overlay/etc/skel/.nomadnetwork/config b/overlay/etc/skel/.nomadnetwork/config
new file mode 100644
index 0000000..edb48ca
--- /dev/null
+++ b/overlay/etc/skel/.nomadnetwork/config
@@ -0,0 +1,334 @@
+# This is the default Nomad Network config file.
+# You should probably edit it to suit your needs and use-case,
+
+[logging]
+# Valid log levels are 0 through 7:
+#   0: Log only critical information
+#   1: Log errors and lower log levels
+#   2: Log warnings and lower log levels
+#   3: Log notices and lower log levels
+#   4: Log info and lower (this is the default)
+#   5: Verbose logging
+#   6: Debug logging
+#   7: Extreme logging
+
+loglevel = 4
+destination = file
+
+[client]
+
+enable_client = yes
+user_interface = text
+downloads_path = ~/Downloads
+notify_on_new_message = yes
+
+# By default, the peer is announced at startup
+# to let other peers reach it immediately.
+announce_at_start = yes
+
+# By default, the client will try to deliver a
+# message via the LXMF propagation network, if
+# a direct delivery to the recipient is not
+# possible.
+try_propagation_on_send_fail = yes
+
+# Nomadnet will periodically sync messages from
+# LXMF propagation nodes by default, if any are
+# present. You can disable this if you want to
+# only sync when manually initiated.
+periodic_lxmf_sync = yes
+
+# The sync interval in minutes. This value is
+# equal to 6 hours (360 minutes) by default.
+lxmf_sync_interval = 360
+
+# By default, automatic LXMF syncs will only
+# download 8 messages at a time. You can change
+# this number, or set the option to 0 to disable
+# the limit, and download everything every time.
+lxmf_sync_limit = 8
+
+# You can specify a required stamp cost for
+# inbound messages to be accepted. Specifying
+# a stamp cost will require untrusted senders
+# that message you to include a cryptographic
+# stamp in their messages. Performing this
+# operation takes the sender an amount of time
+# proportional to the stamp cost. As a rough
+# estimate, a stamp cost of 8 will take less
+# than a second to compute, and a stamp cost
+# of 20 could take several minutes, even on
+# a fast computer.
+required_stamp_cost = None
+
+# You can signal stamp requirements to senders,
+# but still accept messages with invalid stamps
+# by setting this option to True.
+accept_invalid_stamps = False
+
+# The maximum accepted unpacked size for mes-
+# sages received directly from other peers,
+# specified in kilobytes. Messages larger than
+# this will be rejected before the transfer
+# begins.
+max_accepted_size = 500
+
+# The announce stream will only show one entry
+# per destination or node by default. You can
+# change this to show as many announces as have
+# been received, for every destination.
+compact_announce_stream = yes
+
+[textui]
+
+# Amount of time to show intro screen
+intro_time = 1
+
+# You can specify the display theme.
+# theme = light
+theme = dark
+
+# Specify the number of colors to use
+# valid colormodes are:
+# monochrome, 16, 88, 256 and 24bit
+#
+# The default is a conservative 256 colors.
+# If your terminal does not support this,
+# you can lower it. Some terminals support
+# 24 bit color.
+
+# colormode = monochrome
+# colormode = 16
+# colormode = 88
+colormode = 256
+# colormode = 24bit
+
+# By default, unicode glyphs are used. If
+# you have a Nerd Font installed, you can
+# enable this for a better user interface.
+# You can also enable plain text glyphs if
+# your terminal doesn't support unicode.
+
+# glyphs = plain
+glyphs = unicode
+# glyphs = nerdfont
+
+# You can specify whether mouse events
+# should be considered as input to the
+# application. On by default.
+mouse_enabled = True
+
+# What editor to use for editing text.
+editor = nano
+
+# If you don't want the Guide section to
+# show up in the menu, you can disable it.
+hide_guide = no
+
+[node]
+
+# Whether to enable node hosting
+enable_node = no
+
+# The node name will be visible to other
+# peers on the network, and included in
+# announces.
+node_name = None
+
+# Automatic announce interval in minutes.
+# 6 hours by default.
+announce_interval = 360
+
+# Whether to announce when the node starts.
+announce_at_start = Yes
+
+# When Nomad Network is hosting a page-serving
+# node, it can also act as an LXMF propagation
+# node. This is a convenient feature that lets
+# you easily set up and run a propagation node
+# on the network, but it is not as fully
+# featured as using the lxmd program to host a
+# propagation node. For complete control and
+# flexibility, use lxmd to run a PN. For a
+# small local system or network, the built-in
+# PN functionality will suffice for most cases.
+#
+# If there is already a large amount of
+# propagation nodes on the network, or you
+# simply want to run a pageserving-only node,
+# you should disable running a propagation node.
+# Due to lots of propagation nodes being
+# available, this is currently the default.
+
+disable_propagation = Yes
+
+# For clients and other propagation nodes
+# delivering messages via this node, you can
+# configure the minimum required propagation
+# stamp costs. All messages delivered to the
+# propagation node network must have a valid
+# propagation stamp, or they will be rejected.
+# Clients automatically detect the stamp cost
+# for the node they are delivering to, and
+# compute a corresponding stamp before trying
+# to deliver the message to the propagation
+# node.
+#
+# Propagation stamps are easier to verify in
+# large batches, and therefore also somewhat
+# easier to compute for the senders. As such,
+# a reasonable propagation stamp cost should
+# be a bit higher than the normal peer-to-peer
+# stamp costs.
+#
+# Propagation stamps does not incur any extra
+# load for propagation nodes processing them,
+# since they are only required to verify that
+# they are correct, and only the generation
+# is computationally costly. Setting a sensible
+# propagation stamp cost (and periodically
+# checking the average network consensus) helps
+# keep spam and misuse out of the propagation
+# node network.
+
+propagation_cost = 16
+
+# The maximum amount of storage to use for
+# the LXMF Propagation Node message store,
+# specified in megabytes. When this limit
+# is reached, LXMF will periodically remove
+# messages in its message store. By default,
+# LXMF prioritises keeping messages that are
+# new and small. Large and old messages will
+# be removed first. This setting is optional
+# and defaults to 2 gigabytes.
+
+# message_storage_limit = 2000
+
+# The maximum accepted transfer size per in-
+# coming propagation message, in kilobytes.
+# This sets the upper limit for the size of
+# single messages accepted onto this node.
+
+max_transfer_size = 256
+
+# The maximum accepted transfer size per in-
+# coming propagation node sync.
+#
+# If a node wants to propagate a larger number
+# of messages to this node, than what can fit
+# within this limit, it will prioritise sending
+# the smallest messages first, and try again
+# with any remaining messages at a later point.
+
+max_sync_size = 10240
+
+# You can tell the LXMF message router to
+# prioritise storage for one or more
+# destinations. If the message store reaches
+# the specified limit, LXMF will prioritise
+# keeping messages for destinations specified
+# with this option. This setting is optional,
+# and generally you do not need to use it.
+
+# prioritise_destinations = 41d20c727598a3fbbdf9106133a3a0ed, d924b81822ca24e68e2effea99bcb8cf
+
+# You can configure the maximum number of other
+# propagation nodes that this node will peer
+# with automatically. The default is 20.
+
+# max_peers = 20
+
+# You can configure a list of static propagation
+# node peers, that this node will always be
+# peered with, by specifying a list of
+# destination hashes.
+
+# static_peers = e17f833c4ddf8890dd3a79a6fea8161d, 5a2d0029b6e5ec87020abaea0d746da4
+
+# You can specify the interval in minutes for
+# rescanning the hosted pages path. By default,
+# this option is disabled, and the pages path
+# will only be scanned on startup.
+
+# page_refresh_interval = 0
+
+# You can specify the interval in minutes for
+# rescanning the hosted files path. By default,
+# this option is disabled, and the files path
+# will only be scanned on startup.
+
+# file_refresh_interval = 0
+
+[printing]
+
+# You can configure Nomad Network to print
+# various kinds of information and messages.
+
+# Printing messages is disabled by default
+
+print_messages = No
+
+# You can configure a custom template for
+# message printing. If you uncomment this
+# option, set a path to the template and
+# restart Nomad Network, a default template
+# will be created that you can edit.
+
+# message_template = ~/.nomadnetwork/print_template_msg.txt
+
+# You can configure Nomad Network to only
+# print messages from trusted destinations.
+
+# print_from = trusted
+
+# Or specify the source LXMF addresses that
+# will automatically have messages printed
+# on arrival.
+
+# print_from = 76fe5751a56067d1e84eef3e88eab85b, 0e70b5848eb57c13154154feaeeb89b7
+
+# Or allow printing from anywhere, if you
+# are feeling brave and adventurous.
+
+# print_from = everywhere
+
+# You can configure the printing command.
+# This will use the default CUPS printer on
+# your system.
+
+print_command = lp
+
+# You can specify what printer to use
+# print_command = lp -d [PRINTER_NAME]
+
+# Or specify more advanced options. This
+# example works well for small thermal-
+# roll printers:
+# print_command = lp -d [PRINTER_NAME] -o cpi=16 -o lpi=8
+
+# This one is more suitable for full-sheet
+# printers. It will print a QR code at the center of any media
+# your printer will accept, print in portrait mode, and move the message to
+# the top of the print queue:
+# print_command = lp -d [PRINTER_NAME] -o job-priority=100 -o media=Custom.75x75mm -o orientation-requested=3
+
+# But you can modify the size to fit your needs.
+# The custom media option accepts millimeters, centimeters, and
+# inches in a width by length format like so:
+# -o media=Custom.[WIDTH]x[LENGTH][mm,cm,in]
+#
+# The job priority option accepts 1-100, though you can remove it
+# entirely if you aren't concerned with a print queue:
+# -o job-priority=[1-100]
+#
+# Finally, the orientation option allows for 90 degree rotations beginning with 3, so:
+# -o orientation-requested=4 (landscape, 90 degrees)
+# -o orientation-requested=5 (reverse portrait, 180 degrees)
+#
+# Here is the full command with the recommended customizable variables:
+# print_command = lp -d [PRINTER_NAME] -o job-priority=[N] -o media=[MEDIA_SIZE] -o orientation-requested=[N] -o sides=one-sided
+
+# For example, here's a configuration for USB thermal printer that uses the POS-58 PPD driver
+# with rolls 47.98x209.9mm in size:
+# print_command = lp -d [PRINTER_NAME] -o job-priority=100 -o media=custom_47.98x209.9mm_47.98x209.9mm -o sides=one-sided
diff --git a/scripts/install-offline-lib.json b/scripts/install-offline-lib.json
index 871d626..b901f68 100644
--- a/scripts/install-offline-lib.json
+++ b/scripts/install-offline-lib.json
@@ -43,5 +43,10 @@
     "url": "https://reticulum.betweentheborders.com/primer.pdf",
     "file": "primer.pdf",
     "dir": "reticulum"
+  },
+  {
+    "url": "https://github.com/markqvist/Reticulum/releases/download/1.2.5/Reticulum.Manual.pdf",
+    "file": "Reticulum.Manual.pdf",
+    "dir": "reticulum"
   }
 ]