js8call/.svn/pristine/a1/a19309637b69c01a8ad2f3e57147d9fbc64437a4.svn-base

_WSJT-X_ v1.9 suppports a number of features designed for use
on the VHF and higher bands.  These features include:

- *FT8*, a mode designed for making fast QSOs with weak, fading
signals

- *JT4*, a mode particularly useful for EME on the microwave bands

- *JT9* fast modes, useful for scatter propagation on VHF bands

- *JT65*, widely used for EME on VHF and higher bands

- *QRA64*, a mode for EME using a "`Q-ary Repeat Accumulate`" code,
a low-density parity-check (LDPC) code using a 64-character symbol
alphabet

- *MSK144*, a mode for meteor scatter using a binary LDPC code and
Offset Quadrature Phase-Shift Keying (OQPSK).  The resulting waveform
is sometimes called Minimum Shift Keying (MSK).

- *ISCAT*, intended for aircraft scatter and other types of scatter
propagation

- *Echo* mode, for detecting and measuring your own lunar echoes

- *Doppler tracking*, which becomes increasingly important for EME
on bands above 1.2 GHz.

- Optional *Auto-Sequencing* in JT4, JT9, and JT65 as well as FT8 and QRA64.

[[VHF_SETUP]]
=== VHF Setup

To activate the VHF-and-up features:

- On the *Settings | General* tab check *Enable VHF/UHF/Microwave
features* and *Single decode*.

- For EME, check *Decode after EME delay* to allow for extra path
delay on received signals.

- If you will use automatic Doppler tracking and your radio accepts
frequency-setting commands while transmitting, check *Allow Tx
frequency changes while transmitting*.  Transceivers known to permit
such changes include the IC-735, IC-756 Pro II, IC-910-H, FT-847,
TS-590S, TS-590SG, TS-2000 (with Rev 9 or later firmware upgrade),
Flex 1500 and 5000, HPSDR, Anan-10, Anan-100, and KX3.  To gain full
benefit of Doppler tracking your radio should allow frequency changes
under CAT control in 1 Hz steps.

NOTE: If your radio does not accept commands to change frequency
while transmitting, Doppler tracking will be approximated with a
single Tx frequency adjustment before a transmission starts, using a
value computed for the middle of the Tx period.

- On the *Radio* tab select *Split Operation* (use either *Rig* or
*Fake It*; you may need to experiment with both options to find one
that works best with your radio).

- On the right side of the main window select *Tab 1* to present the
traditional format for entering and choosing Tx messages.

The main window will reconfigure itself as necessary to display
controls supporting the features of each mode.

- If you are using transverters, set appropriate frequency offsets on
the *Settings | Frequencies* tab.  Offset is defined as (transceiver
dial reading) minus (on-the-air frequency).  For example, when using a
144 MHz radio at 10368 MHz, *Offset (MHz)* = (144 - 10368) =
-10224.000.  If the band is already in the table, you can edit the
offset by double clicking on the offset field itself.  Otherwise a new
band can be added by right clicking in the table and selecting
*Insert*.

image::Add_station_info.png[align="center",alt="Station information"]

- On the *View* menu, select *Astronomical data* to display a window
with important information for tracking the Moon and performing
automatic Doppler control.  The right-hand portion of the window
becomes visible when you check *Doppler tracking*.

image::Astronomical_data.png[align="center",alt="Astronomical data"]

Five different types of Doppler tracking are provided:

- Select *Full Doppler to DX Grid* if you know your QSO partner's locator
and he/she will not be using any Doppler control.

- Select *Own Echo* to enable EME Doppler tracking of your receive
frequency to your own echo frequency. Your Tx frequency will remain fixed
and is set to the Sked frequency.  This mode can be used when announcing 
your CQ call on a specific frequency and listening on your own echo
frequency.  It can also be used for echo testing with Echo mode.

- Select *Constant frequency on Moon* to correct for your own one-way
Doppler shift to or from the Moon.  If your QSO partner does the same
thing, both stations will have the required Doppler compensation.
Moreover, anyone else using this option will hear both of you
without the need for manual frequency changes.

- Select *On Dx Echo* when your QSO partner is not using automated 
Doppler tracking, and announces his/her transmit frequency and listening
on their own echo frequency. When clicked, this Doppler method will 
set your rig frequency on receive to correct for the mutual Doppler 
shift.  On transmit, your rig frequency will be set so that your
QSO partner will receive you on the same frequency as their own echo
at the start of the QSO. As the QSO proceeds, your QSO partner will 
receive you on this starting frequency so that they do not have to 
retune their receiver as the Doppler changes.  Sked frequency in this 
case is set to that announced by your QSO partner.

- Select *Call DX* after tuning the radio manually to find a station,
with the Doppler mode initally set to *None*. You may be tuning the band
looking for random stations, or to a frequency where a station has been
seen on an SDR display.  It is usually necessary to hold down the Ctrl key
while tuning the radio. From the moment *Call DX* is pressed, your 
transmit frequency is set so that your echo will fall on the same 
frequency you (and the DX station) are listening. 

- See <<ASTRODATA,Astronomical Data>> for details on the quantities
displayed in this window.

=== JT4

JT4 is designed especially for EME on the microwave bands, 2.3 GHz and
above.

- Select *JT4* from the *Mode* menu.  The central part of the main
window will look something like this:

image::VHF_controls.png[align="center",alt="VHF Controls"]

- Select the desired *Submode*, which determines the spacing of
transmitted tones. Wider spacings are used on the higher microwave
bands to allow for larger Doppler spreads. For example, submode JT4F
is generally used for EME on the 5.7 and 10 GHz bands.

- For EME QSOs some operators use short-form JT4 messages consisting
of a single tone.  To activate automatic generation of these messages,
check the box labeled *Sh*. This also enables the generation of a
single tone at 1000Hz by selecting Tx6, to assist in finding signals
initially.  The box labeled *Tx6* toggles the Tx6 message from 1000Hz
to 1250Hz to indicate to the other station that you are ready to
receive messages.

- Select *Deep* from the *Decode* menu.  You may also choose to
*Enable averaging* over successive transmissions and/or *Enable deep
search* (correlation decoding).

image::decode-menu.png[align="center",alt="Decode Menu"]

The following screen shot shows one transmission from a 10 GHz EME
QSO using submode JT4F.

image::JT4F.png[align="center",alt="JT4F"]

=== JT65

In many ways JT65 operation on VHF and higher bands is similar to HF
usage, but a few important differences should be noted.  Typical
VHF/UHF operation involves only a single signal (or perhaps two or
three) in the receiver passband.  You may find it best to check
*Single decode* on the *Settings -> General* tab.  There will be
little need for *Two pass decoding* on the *Advanced* tab.  With VHF
features enabled the JT65 decoder will respond to special message
formats often used for EME: the OOO signal report and two-tone
shorthand messages for RO, RRR, and 73.  These messages are always
enabled for reception; they will be automatically generated for
transmission if you check the shorthand message box *Sh*.

*Deep* on the *Decode* menu will be automatically selected.  You may
optionally include *Enable averaging*, *Enable Deep search*, and
*Enable AP*.

The following screen shot shows three transmissions from a 144 MHz EME
QSO using submode JT65B and shorthand messages.  Take note of the
colored tick marks on the Wide Graph frequency scale.  The green
marker at 1220 Hz indicates the selected QSO frequency (the frequency
of the JT65 Sync tone) and the *F Tol* range.  A green tick at 1575 Hz
marks the frequency of the highest JT65 data tone.  Orange markers
indicate the frequency of the upper tone of the two-tone signals for
RO, RRR, and 73.

image::JT65B.png[align="center",alt="JT65B"]

=== QRA64

QRA64 is designed for EME on VHF and higher bands; its
operation is generally similar to JT4 and JT65.  The following screen
shot shows an example of a QRA64C transmission from DL7YC recorded at
G3WDG over the EME path at 24 GHz.  Doppler spread on the path was 78
Hz, so although the signal is reasonably strong its tones are
broadened enough to make them hard to see on the waterfall.  The
triangular red marker below the frequency scale shows that the decoder
has achieved synchronization with a signal at approximately 967 Hz.

image::QRA64.png[align="center",alt="QRA64"]

The QRA64 decoder makes no use of a callsign database.  Instead, it
takes advantage of _a priori_ (AP) information such as one's own
callsign and the encoded form of message word `CQ`.  In normal usage,
as a QSO progresses the available AP information increases to include
the callsign of the station being worked and perhaps also his/her
4-digit grid locator.  The decoder always begins by attempting to
decode the full message using no AP information.  If this attempt
fails, additional attempts are made using available AP information to
provide initial hypotheses about the message content.  At the end of
each iteration the decoder computes the extrinsic probability of the
most likely value for each of the message's 12 six-bit information
symbols.  A decode is declared only when the total probability for all
12 symbols has converged to an unambiguous value very close to 1.

For EME QSOs some operators use short-form QRA64 messages consisting
of a single tone.  To activate automatic generation of these messages,
check the box labeled *Sh*.  This also enables the generation of a
single tone at 1000Hz by selecting Tx6, to assist in finding  signals
initially, as the QRA64 tones are often not visible on the waterfall.
The box labeled *Tx6* switches the Tx6 message from 1000Hz to 1250Hz
to indicate to the other station that you are ready to receive messages.

TIP: QRA64 is different from JT65 in that the decoder attempts to find
and decode only a single signal in the receiver passband.  If many
signals are present you may be able to decode them by double-clicking
on the lowest tone of each one in the waterfall.

TIP: G3WDG has prepared a more detailed tutorial on using {QRA64_EME}. 

=== ISCAT

ISCAT is a useful mode for signals that are weak but more or less
steady in amplitude over several seconds or longer.  Aircraft scatter
at 10 GHz is a good example.  ISCAT messages are free-format and may
have any length from 1 to 28 characters.  This protocol includes no
error-correction facility.

=== MSK144

Meteor-scatter QSOs can be made any time on the VHF bands at distances
up to about 2100 km (1300 miles).  Completing a QSO takes longer in
the evening than in the morning, longer at higher frequencies, and
longer at distances close to the upper limit.  But with patience, 100
Watts or more, and a single yagi it can usually be done.  The
following screen shot shows two 15-second MSK144 transmissions from
W5ADD during a 50 MHz QSO with K1JT, at a distance of about 1800 km
(1100 mi).  The decoded segments have been marked on the *Fast
Graph* spectral display.

image::MSK144.png[align="center",alt="MSK144"]

Unlike other _WSJT-X_ modes, the MSK144 decoder operates in real time
during the reception sequence.  Decoded messages will appear on your
screen almost as soon as you hear them.

To configure _WSJT-X_ for MSK144 operation:

- Select *MSK144* from the *Mode* menu.

- Select *Fast* from the *Decode* menu.

- Set the audio receiving frequency to *Rx 1500 Hz*.

- Set frequency tolerance to *F Tol 100*.

- Set the *T/R* sequence duration to 15 s.

- To match decoding depth to your computer's capability, click
*Monitor* (if it's not already green) to start a receiving sequence.
Observe the percentage figure displayed on the _Receiving_ label in
the Status Bar:

image::Rx_pct_MSK144.png[align="center",alt="MSK144 Percent CPU"]

- The displayed number (here 17%) indicates the fraction of available
time being used for execution of the MSK144 real-time decoder.  If
this number is well below 100% you may increase the decoding depth
from *Fast* to *Normal* or *Deep*, and increase *F Tol* from 100 to
200 Hz.

NOTE: Most modern multi-core computers can easily handle the optimum
parameters *Deep* and *F Tol 200*.  Older and slower machines may not
be able to keep up at these settings; at the *Fast* and *Normal*
settings there will be a small loss in decoding capability (relative
to *Deep*) for the weakest pings.

- T/R sequences of 15 seconds or less requires selecting your
transmitted messages very quickly.  Check *Auto Seq* to have the
computer make the necessary decisions automatically, based on the
messages received.

- For operation at 144 MHz or above you may find it helpful to use
short-format *Sh* messages for Tx3, Tx4, and Tx5.  These messages are
20 ms long, compared with 72 ms for full-length MSK144 messages.
Their information content is a 12-bit hash of the two callsigns,
rather than the callsigns themselves, plus a 4-bit numerical report,
acknowledgment (RRR), or sign-off (73).  Only the intended recipient
can decode short-messages.  They will be displayed with the callsigns
enclosed in <> angle brackets, as in the following model QSO

 CQ K1ABC FN42
                    K1ABC W9XYZ EN37
 W9XYZ K1ABC +02
                    <K1ABC W9XYZ> R+03
 <W9XYZ K1ABC> RRR
                    <K1ABC W9XYZ> 73


NOTE: There is little or no advantage to using MSK144 *Sh*
messages at 50 or 70 MHz.  At these frequencies, most pings are long
enough to support standard messages -- which have the advantage of
being readable by anyone listening in.

=== Echo Mode

*Echo* mode allows you to make sensitive measurements of your own
lunar echoes even when they are too weak to be heard. Select *Echo*
from the *Mode* menu, aim your antenna at the moon, pick a clear
frequency, and toggle click *Tx Enable*. _WSJT-X_ will then cycle
through the following loop every 6 seconds:

1. Transmit a 1500 Hz fixed tone for 2.3 s
2. Wait about 0.2 s for start of the return echo
3. Record the received signal for 2.3 s
4. Analyze, average, and display the results
5. Repeat from step 1

To make a sequence of echo tests:

- Select *Echo* from the *Mode* menu.

- Check *Doppler tracking* and *Constant frequency on the Moon* on the
Astronomical Data window.

- Be sure that your rig control has been set up for _Split Operation_,
using either *Rig* or *Fake It* on the *Settings | Radio* tab.

- Click *Enable Tx* on the main window to start a sequence of 6-second
cycles.

- _WSJT-X_ calculates and compensates for Doppler shift automatically.
As shown in the screen shot below, when proper Doppler corrections
have been applied your return echo should always appear at the center
of the plot area on the Echo Graph window.

image::echo_144.png[align="center",alt="Echo 144 MHz"]

=== VHF+ Sample Files

Sample recordings typical of QSOs using the VHF/UHF/Microwave modes
and features of _WSJT-X_ are available for
<<DOWNLOAD_SAMPLES,download>>.  New users of the VHF-and-up features
are strongly encouraged to practice decoding the signals in these
files.